3500/22-01-01-00 288055-01 BENTLY NEVADA  Power Board

The monitoris configured using Bently Nevada Monitor Configuration* application. The SPA interface on the 2300/25 is configured using System 1* Classic application. The monitoring system consists of:  A 2300 monitor with network connection l Bently Nevada Monitor Configuration application l System 1 Evolution or System 1 Classic application l Sensors and interface as needed to accommodate the system This connection is available for channel 1 and channel 2. This interface consists of two signal connections which are A/+ (positive) and B/– (negative). This connection type is designed to function with 2-Wire ICP type transducers such as AM3100T2-Z2 or custom transducer. To function with these transducers, a special biasing circuit is provided through the A/+ and B/- connections. Othertransducers may also function if the following constraints are met: l Bias is -12VDC l Have a typical current of 3.3 mA ± 5% l Output signalrange is within 0VDC to -24VDC l Typical frequency range from 0Hz to 20KHz  Config Lock (Labeled: 1S, 1C): This is used to prevent unwanted orinadvertent changes to the monitorthat may disrupt or alter monitoring functionality. The restricted functionality includes: l Configuration download l Firmware upgrades l Network IP changes to the monitorthrough software l Buried button reset settings function (reset user name & password & IP) Some features that are still allowed include: l Software switch changes such as Alarm/Relay Inhibit, and Bypass l All hardware contacts and buttons except buried button reset settings function l Time and date changes and User management Alarm Reset (Labeled: 2S, 2C): Momentarily short these contacts to reset latched alarms, and latched relays. Latching is a configurable option that causes a state such as an alarm to persist even if the condition that caused the alarm is no longer present. Alarm Reset allows those latched states to go to their non-active state if the original condition that caused the state no longer exists. Bypass (Labeled: 3S, 3C): This is used to prevent the monitorfrom driving the Invalid, Not OK, Protection Fault, and relays even if there is a hardware fault. All measurements will be marked as BYPASS, latched alarms will be reset, and new alarms will be prevented

The structure and details of the product：

Please make an inquiry for more models

　　BENTLY NEVADA BENTLY9200-01-05-10-00

　　BENTLY NEVADA 125388-01

　　BENTLY NEVADA 127610-01 3500/15

　　BENTLY NEVADA 128275-01

　　BENTLY NEVADA 135813-01

　　BENTLY NEVADA 136719-01

　　BENTLY NEVADA 3300/03 3300/03-01-00

　　BENTLY NEVADA 3300/05-23-00-00

　　BENTLY NEVADA 3300/16 3300/0-00-00

　　BENTLY NEVADA 3300/20 3300/20-0

　　BENTLY NEVADA 3300/35 3300/35-2

　　BENTLY NEVADA 3300/46 3300/46-46-04-02-01

　　BENTLY NEVADA 3300/50 3300/50-01-01-00-00

　　BENTLY NEVADA 3300/65 3300/65-1-00

　　BENTLY NEVADA 3300XL 8MM

　　BENTLY NEVADA 330101-00-

　　BENTLY NEVADA 330101-00-28-10-02-05

　　BENTLY NEVADA 330103-00-03-10-02-05

　　BENTLY NEVADA 330103-00-04-10-02-05

　　BENTLY NEVADA 330103-00-05-05-02-05

　　BENTLY NEVADA 330103-00-05-10-02-05

　　BENTLY NEVADA 330103-00-

　　BENTLY NEVADA 330103-00-

　　BENTLY NEVADA 330103-05-10-10-02-05

　　BENTLY NEVADA 330103-10-

　　BENTLY NEVADA 330104-00-04-10-02-05

　　BENTLY NEVADA 330104-00-06-10-11-00

　　BENTLY NEVADA 330104-00-11-10-02-05

　　BENTLY NEVADA 330104-05-

　　BENTLY NEVADA 330104-0

　　BENTLY NEVADA 330104-0

　　BENTLY NEVADA 330104-5

　　BENTLY NEVADA 330105-02-12-90-02-05

　　BENTLY NEVADA 330130-040-02-05

　　BENTLY NEVADA 330130-045-02-05

Other best-selling products：