89414-01 BENTLY NEVADA  Servo Controller

Perform the following procedure to assure proper probe installation. The observed surface must remain motionless while gapping the probe. The probe can be gapped mechanically or electrically. Use either steps a and b or steps a and c. a. Before installing the probe into its mounting hole, ensure the tapped hole is free of foreign material. If necessary, use an appropriate tap to clean the threads. Before the probe is threaded, disconnect the probe integral cable from the Proximitor or make sure it is free to turn to prevent twisting the lead. b. The probe can be gapped mechanically. Thread it into the mounting and use a nonmetallic feeler gauge to set the gap. A nonmetallic feeler gauge must be used to prevent scratching of the probe tip or the observed surface. The probe can also be gapped electrically by connecting the probe cable to the Proximitor (see CAUTION below). Apply the proper input voltage (-18 Vdc or -24 Vdc) to the Proximitor. Connect a digital multimeter to the Proximitor output. Thread the probe into the mounting, and observe the transducer output voltage. As the probe is threaded, the transducer output voltage remains low or gives a false reading because it is sensing the surrounding mounting material. See Figure 2-3. As the probe tip extends through the mounting, the transducer output voltage will increase to its maximum output and then decrease as it approaches the observed surface. By cross-referencing this voltage with the probe calibration curve in Appendix C, the proper gap can be set. d. When the probe is properly gapped, secure it by tightening the jam nut (locknut). Care should be taken so the jam nut is not secured so tightly the threads are stripped.

The structure and details of the product：

Please make an inquiry for more models

　　BENTLY NEVADA BENTLY9200-01-05-10-00

　　BENTLY NEVADA 125388-01

　　BENTLY NEVADA 127610-01 3500/15

　　BENTLY NEVADA 128275-01

　　BENTLY NEVADA 135813-01

　　BENTLY NEVADA 136719-01

　　BENTLY NEVADA 3300/03 3300/03-01-00

　　BENTLY NEVADA 3300/05-23-00-00

　　BENTLY NEVADA 3300/16 3300/0-00-00

　　BENTLY NEVADA 3300/20 3300/20-0

　　BENTLY NEVADA 3300/35 3300/35-2

　　BENTLY NEVADA 3300/46 3300/46-46-04-02-01

　　BENTLY NEVADA 3300/50 3300/50-01-01-00-00

　　BENTLY NEVADA 3300/65 3300/65-1-00

　　BENTLY NEVADA 3300XL 8MM

　　BENTLY NEVADA 330101-00-

　　BENTLY NEVADA 330101-00-28-10-02-05

　　BENTLY NEVADA 330103-00-03-10-02-05

　　BENTLY NEVADA 330103-00-04-10-02-05

　　BENTLY NEVADA 330103-00-05-05-02-05

　　BENTLY NEVADA 330103-00-05-10-02-05

　　BENTLY NEVADA 330103-00-

　　BENTLY NEVADA 330103-00-

　　BENTLY NEVADA 330103-05-10-10-02-05

　　BENTLY NEVADA 330103-10-

　　BENTLY NEVADA 330104-00-04-10-02-05

　　BENTLY NEVADA 330104-00-06-10-11-00

　　BENTLY NEVADA 330104-00-11-10-02-05

　　BENTLY NEVADA 330104-05-

　　BENTLY NEVADA 330104-0

　　BENTLY NEVADA 330104-0

　　BENTLY NEVADA 330104-5

　　BENTLY NEVADA 330105-02-12-90-02-05

　　BENTLY NEVADA 330130-040-02-05

　　BENTLY NEVADA 330130-045-02-05

Other best-selling products：