1738-EXT1  A-B  Circuit Board

Installation Requirements Related to EN 61800-3 and the EMC Directive • The drive must be earthed (grounded) as described in Connections and Grounding on page 45. See General Grounding Requirements on page 16 for additional grounding recommendations. • Output power wiring to the motor must employ cables with a braided shield providing 75% or greater coverage, or the cables must be housed in metal conduit, or equivalent shield must be provided. Continuous shielding must be provided from the drive enclosure to the motor enclosure. Both ends of the motor cable shield (or conduit) must terminate with a low-impedance connection to earth. Drive Frames A...E: At the drive end of the motor, either a. The cable shield must be clamped to a properly installed “EMC Plate” for the drive. Kit number 25-EMC1-Fx. or b. The cable shield or conduit must terminate in a shielded connector installed in an EMC plate, conduit box, or similar. • At the motor end, the motor cable shield or conduit must terminate in a shielded connector which must be properly installed in an earthed motor wiring box attached to the motor. The motor wiring box cover must be installed and earthed. • All control (I/O) and signal wiring to the drive must use cable with a braided shield providing 75% or greater coverage, or the cables must be housed in metal conduit, or equivalent shielding must be provided. When shielded cable is used, the cable shield should be terminated with a low impedance connection to earth at only one end of the cable, preferably the end where the receiver is located. When the cable shield is terminated at the drive end, it may be terminated either by using a shielded connector in conjunction with a conduit plate or conduit box, or the shield may be clamped to an “EMC plate.” • Motor cabling must be separated from control and signal wiring wherever possible. • Maximum motor cable length must not exceed the maximum length indicated in PowerFlex 525 RF Emission Compliance and Installation Requirements on page 45 for compliance with radio frequency emission limits for the specific standard and installation environment.

The structure and details of the product：

Please make an inquiry for more models

　　AB 1756-LSP

　　AB 1756-LSP/B

　　AB 1756-M02AE

　　AB 1756-M02AS

　　AB 1756-M03SE

　　AB 1756-M08SE

　　AB 1756-M1

　　AB 1756-M16S

　　AB 1756-M16SE

　　AB 1756-N2

　　AB 1756-OA16

　　AB 1756-OA16I

　　AB 1756-OB16D

　　AB 1756-OB16E

　　AB 1756-OB16I

　　AB 1756-OB16I/A

　　AB 1756-OB16IEF

　　AB 1756-OB16IS

　　AB 1756-OB32

　　AB 1756-OB32/A

　　AB 1756-OB8

　　AB 1756-OF4

　　AB 1756-OF41794-ADN

　　AB 1756-OF6CI

　　AB 1756-OF6VI

　　AB 1756-OF8

　　AB 1756-OF8/A

　　AB 1756-OF81

　　AB 1756-OG16

　　AB 1756-OH8I

　　AB 1756-ON8

　　AB 1756-OV16E

　　AB 1756-OV32E

　　AB 1756-OW16I

　　AB 1756-OW16I/A

　　AB 1756-OX8I

　　AB 1756-PA72

　　AB 1756-PA72/B

　　AB 1756-PA72/C

　　AB 1756-PA75

　　AB 1756-PA75/A

　　AB 1756-PA75/B

　　AB 1756-PA75R

　　AB 1756-PAR2

　　AB 1756-PB72

　　AB 1756-PB75

　　AB 1756-PB75R

　　AB 1756-PBR2

　　AB 1756-PC75

　　AB 1756-PLS

　　AB 1756-PSCA2/A

　　AB 1756-RM

　　AB 1756-RM2

　　AB 1756-RM2/A

　　AB 1756SC-CTR8

　　AB 1756-SRM/B

　　AB 1756-TBCH

　　AB 1756-TBNH

　　AB 1756-TBS6H

Other best-selling products：