2198-P031 A-B  Analog Input Module

Power Cable Types Acceptable for 200…600 Volt Installations Various cable types are acceptable for drive installations. For many installations, unshielded cable is adequate, provided it can be separated from sensitive circuits. As an approximate guide, allow a spacing of 0.3 meters (1 foot) for every 10 meters (32.8 feet) of length. In all cases, long parallel runs must be avoided. Do not use cable with an insulation thickness less than or equal to 15 mils (0.4mm/0.015 in.). Use Copper wire only. Wire gauge requirements and recommendations are based on 75 °C (167 °F). Do not reduce wire gauge when using higher temperature wire. See table below.

THHN, THWN or similar wire is acceptable for drive installation in dry environments provided adequate free air space and/or conduit fill rates limits are provided. Do not use THHN or similarly coated wire in wet areas. Any wire that is chosen must have a minimum insulation thickness of 15 mils and should not have large variations in insulation concentricity. Shielded/Armored Cable Shielded cable contains all general benefits of multi-conductor cable with the added benefit of a copper braided shield that can contain much of the noise that is generated by a typical AC drive. Strong consideration for shielded cable should be given in installations with sensitive equipment such as weigh scales, capacitive proximity switches and other devices that may be affected by electrical noise in the distribution system. Applications with large numbers of drives in a similar location, imposed EMC regulations or a high degree of communications/ networking are also good candidates for shielded cable. Shielded cable may also help reduce shaft voltage and induced bearing currents for some applications. In addition, the increased impedance of shielded cable may help extend the distance that the motor can be located from the drive without the addition of motor protective devices such as terminator networks. Consideration should be given to all general specifications that are dictated by the environment of the installation, including temperature, flexibility, moisture characteristics and chemical resistance. In addition, a braided shield should be included and be specified by the cable manufacturer as having coverage of at least 75%. An additional foil shield can greatly improve noise containment. A good example of recommended cable is Belden 295xx (xx determines gauge). This cable has four (4) XLPE insulated conductors with a 100% coverage foil and an 85% coverage copper braided shield (with drain wire) surrounded by a PVC jacket. Other types of shielded cable are available, but the selection of these types may limit the allowable cable length. Particularly, some of the newer cables twist four conductors of THHN wire and wrap them tightly with a foil shield. This construction can greatly increase the cable charging current required and reduce the overall drive performance. Unless specified in the individual distance tables as tested with the drive, these cables are not recommended and their performance against the lead length limits supplied is not known.

The structure and details of the product：

Please make an inquiry for more models

　　AB 1756-LSP

　　AB 1756-LSP/B

　　AB 1756-M02AE

　　AB 1756-M02AS

　　AB 1756-M03SE

　　AB 1756-M08SE

　　AB 1756-M1

　　AB 1756-M16S

　　AB 1756-M16SE

　　AB 1756-N2

　　AB 1756-OA16

　　AB 1756-OA16I

　　AB 1756-OB16D

　　AB 1756-OB16E

　　AB 1756-OB16I

　　AB 1756-OB16I/A

　　AB 1756-OB16IEF

　　AB 1756-OB16IS

　　AB 1756-OB32

　　AB 1756-OB32/A

　　AB 1756-OB8

　　AB 1756-OF4

　　AB 1756-OF41794-ADN

　　AB 1756-OF6CI

　　AB 1756-OF6VI

　　AB 1756-OF8

　　AB 1756-OF8/A

　　AB 1756-OF81

　　AB 1756-OG16

　　AB 1756-OH8I

　　AB 1756-ON8

　　AB 1756-OV16E

　　AB 1756-OV32E

　　AB 1756-OW16I

　　AB 1756-OW16I/A

　　AB 1756-OX8I

　　AB 1756-PA72

　　AB 1756-PA72/B

　　AB 1756-PA72/C

　　AB 1756-PA75

　　AB 1756-PA75/A

　　AB 1756-PA75/B

　　AB 1756-PA75R

　　AB 1756-PAR2

　　AB 1756-PB72

　　AB 1756-PB75

　　AB 1756-PB75R

　　AB 1756-PBR2

　　AB 1756-PC75

　　AB 1756-PLS

　　AB 1756-PSCA2/A

　　AB 1756-RM

　　AB 1756-RM2

　　AB 1756-RM2/A

　　AB 1756SC-CTR8

　　AB 1756-SRM/B

　　AB 1756-TBCH

　　AB 1756-TBNH

　　AB 1756-TBS6H

Other best-selling products：