MPL-B320P-RJ72AA A-B  Control Unit

Because of the variety of uses for the products described in this publication, those responsible for the application and use of this control equipment must satisfy themselves that all necessary steps have been taken to assure that each application and use meets all performance and safety requirements, including any applicable laws, regulations, codes and standards. The illustrations, charts, sample programs and layout examples shown in this guide are intended solely for purposes of example. Since there are many variables and requirements associated with any particular installation, Allen-Bradley® does not assume responsibility or liability (to include intellectual property liability) for actual use based upon the examples shown in this publication. Allen-Bradley publication SGI-1.1, Safety Guidelines for the Application, Installation and Maintenance of Solid-State Control (available from your local Allen-Bradley office), describes some important differences between solid-state equipment and electromechanical devices that should be taken into consideration when applying products such as those described in this publication. Reproduction of the contents of this copyrighted publication, in whole or part, without written permission of Rockwell Automation®, is prohibited

The Ultra3000 Digital Servo Drive Installation Manual Document Update, publication 2098-DU003B-EN-P, includes important information about changes and updates to this Ultra3000 Digital Servo Drive Installation Manual. The document update used to be provided as a separate document, but is now incorporated into this installation manual, in the section immediately following this Summary of Changes section, and before the Table of Contents. Before using this installation manual, read and understand the changes and updates identified in the document update section. No engineering or editorial changes have been made to either the document update or the installation manual; therefore, the publication dates and revisions of each respective manual did not change. The publication date of this Summary of Changes section indicates the date that the combined manuals were released.

Every time a slave station responds or doesn’t respond to its poll packet, the master station automatically updates its active node list (again, even if it’s in program mode). In this list, one bit is assigned to each possible slave station address (0 to 254). If a slave station doesn’t respond when it is polled, its active node list bit is cleared. If it does respond when it is polled, its active node bit is set. Besides being an excellent online troubleshooting tool, two common uses of the active node list are to report good/bad communication status for all slave stations to an operator interface connected to the master station for monitoring, alarming and logging purposes, and to precondition MSG instructions to each particular slave.

This second use is based on the supposition that if a slave station didn’t respond the last time it was polled (which was just a few seconds ago, if that long), then chances are it won’t be able to receive and respond to a MSG instruction now, and so it would most likely just end up going through the maximum number of retries and timeouts before completing in error (which slows down both the poll scan and any other messaging going on). Using this technique, the minimum time to message to every responding slave station actually decreases as the number of slave stations that can’t respond increases.

Polled report-by-exception lets a slave station initiate data transfer to its master station, freeing the master station from having to constantly read blocks of data from each slave station to determine if any slave input or data changes have occurred. Instead, through user programming, the slave station monitors its own inputs for a change of state or data, which triggers a block of data to be written to the master station when the master station polls the slave.

If your SCADA application is time-critical and any two or more of the following apply, then you can benefit from polled report-by-exception messaging: • communication channel is slow (2400 bps or less) • average number of words of data to monitor in each slave station is greater than five • number of slave stations is greater than ten

The structure and details of the product：

Please make an inquiry for more models

　　AB 1756-LSP

　　AB 1756-LSP/B

　　AB 1756-M02AE

　　AB 1756-M02AS

　　AB 1756-M03SE

　　AB 1756-M08SE

　　AB 1756-M1

　　AB 1756-M16S

　　AB 1756-M16SE

　　AB 1756-N2

　　AB 1756-OA16

　　AB 1756-OA16I

　　AB 1756-OB16D

　　AB 1756-OB16E

　　AB 1756-OB16I

　　AB 1756-OB16I/A

　　AB 1756-OB16IEF

　　AB 1756-OB16IS

　　AB 1756-OB32

　　AB 1756-OB32/A

　　AB 1756-OB8

　　AB 1756-OF4

　　AB 1756-OF41794-ADN

　　AB 1756-OF6CI

　　AB 1756-OF6VI

　　AB 1756-OF8

　　AB 1756-OF8/A

　　AB 1756-OF81

　　AB 1756-OG16

　　AB 1756-OH8I

　　AB 1756-ON8

　　AB 1756-OV16E

　　AB 1756-OV32E

　　AB 1756-OW16I

　　AB 1756-OW16I/A

　　AB 1756-OX8I

　　AB 1756-PA72

　　AB 1756-PA72/B

　　AB 1756-PA72/C

　　AB 1756-PA75

　　AB 1756-PA75/A

　　AB 1756-PA75/B

　　AB 1756-PA75R

　　AB 1756-PAR2

　　AB 1756-PB72

　　AB 1756-PB75

　　AB 1756-PB75R

　　AB 1756-PBR2

　　AB 1756-PC75

　　AB 1756-PLS

　　AB 1756-PSCA2/A

　　AB 1756-RM

　　AB 1756-RM2

　　AB 1756-RM2/A

　　AB 1756SC-CTR8

　　AB 1756-SRM/B

　　AB 1756-TBCH

　　AB 1756-TBNH

　　AB 1756-TBS6H

Other best-selling products：